
Fixed: WPS Light Blinking on Rockspace Extender
The Rockspace WiFi range extender contains a number of lights. Each light has a certain function. By examining how the lights behave, you may determine how your Rockspace extender is currently performing. Just in case, if the LEDs behave abnormally you will be alerted that something is wrong with the device and that it needs care. If the WPS light continues to flicker for an extended amount of time, your extender demands some troubleshooting. In this article, we’ll explain about the WPS light blinking issue, how it works, and why the problem has arisen while also giving you detailed advice on how to fix it.
What is WPS?
Before you begin the troubleshooting steps, it is necessary to understand what the WPS (WiFi Protected Setup) means. It is a wireless network security standard. With the help of this, you connect your extender to your existing Wi-Fi network quickly. When you press the WPS button on your extender and your router simultaneously, the WPS light should blink to indicate that the two devices are attempting to establish a connection.
Causes: Rockspace Extender WPS Light Blinking
There are plenty of reasons why your Rockspace range extender WPS light blinking issue arises. Here is a list of some common factors.
Failed WPS Connection
One of the most basic causes for a blinking WPS light is a failed WPS connection attempt between the wireless devices.
WiFi Interference
Interference from other electronic devices, metal objects, neighboring networks, or physical obstacles can disturb the WPS process and lead to a blinking light.
WPS Timeout
The flashing may also indicate a WPS timeout, which means that the extender couldn’t establish a connection with the router within the allocated time.
Outdated Firmware
Corrupted firmware on your Rockspace WiFi range extender can also cause connectivity problems, including the blinking WPS light.
Solutions: Range Extender WPS Light Blinking Issue
1. Restart Your Rockspace Extender
The very first way to fix the WPS light blinking on the extender is to power cycle the extender. Restarting works like a remedy to get rid of the technical hiccups. For reboot, turn off your Rockspace extender and remove it from the wall socket. Wait for a few moments. Now, insert back the extender into a power source, and turn on the switch.
2. Check Power Supply
The power supply to both devices should be sufficient while you attempt to connect the Rockspace extender to the host router using the WPS button during the setup process. Perhaps the connection was disrupted and could not be made because of the fluctuating power supply.
The power supply should be checked first, as advised. Both the power cables and the power sockets should be examined. Make the required adjustments, plug in the extender and router, and then try the WPS setup procedure.
3. Check the Connection
Start by ensuring that your Rockspace WiFi extender is properly plugged into a well-working power socket and turned on. Make sure all cables are securely connected. Sometimes, a loose connection can lead to connectivity problems.
4. Verify Internet Connection
The internet connection must be steady and uninterrupted during setup. It so happened that the WPS setup procedure was not carried out properly owing to a bad internet connection, which led to the Rockspace extender WPS light blinking issue. If there is a problem with the internet supply, contact your ISP. You shouldn’t try connecting the devices again unless you are certain that the internet connection is working flawlessly.
5. Reposition the Extender
Be sure that your Rockspace range extender is placed in an optimal location. It should be within range of your router but not too far away. Keep it away from physical obstructions like walls and metal objects that can interfere with the Wi-Fi signal.
6. Perform Factory Reset
If the aforementioned troubleshooting hacks bear no result, then chances are that your WiFi extender has been configured partially. So, it is time to perform a factory default reset of your Rockspace wireless range extender. It can be done by pressing the Reset button. To reset your extender, follow the steps given below:
- Firstly, disconnect the wireless range extender from the host router.
- Thereafter, look for the reset button on your extender.
- As soon as you find the button, press or hold it gently.
- Wait for a little while and release the button.
In this way, your Rockspace extender resets to its default settings. Now, connect the client device to the extender network i.e. Rockspace_Ext, and configure your extender again.
The Final Notes
Coming across the WPS light blinking on the Rockspace extender issue is quite common. But, what matters is how you resolve it. If you take the help of the troubleshooting tips mentioned in this post, you will surely be able to fix it in no time.